Showing posts with label audio. Show all posts
Showing posts with label audio. Show all posts

Wednesday, November 19, 2014

USB Audio Interface based DAC PCM2902

- 0 comments

This is the circuit quality preamplifier with built-in USB DAC for my Leachamp power amplifier. Scheme is PCM2902 datasheet. Circuit includes DAC and ADC, SPDIF input and output of HID and with 3 buttons + MUTE, VOL-and VOL.

For playback of high quality needed for external low-drop voltage stabilizer for the DAC. LP2951CM DAC is used, which was readily available in local stores. Output voltage is fixed at about 3.7 V with two resistors. Circuit board is designed with regard to the placement of good land, and the separation of digital and analog ground. These earth are connected in a single point in a USB connector.


The PCM2902 data sheet is recommended to connect a low pass filter the DAC output to filter high frequencies above audioband produced by the conversion of oversampling. Digital integrated circuits that includes LPF filter frequency above 100 kHz. In the Notes application filter on the pages of the manufacturer recommends first-order LPF (simple RC) or 2 nd order with amplifiers operating as a preamp that works well. I simple RC LPF with the recommended values ​​R and C 1k 4N7. It is best to use the scroll-type ceramic capacitor in place. I did not hear the difference in sound between the connection filter or not, but with respect to other components in an audio chain is best used. For maximum cutoff frequency that can change the capacitor value of 3n3
[Continue reading...]

Tuesday, November 18, 2014

20W Surround audio amplifier with SI 1020G

- 0 comments
Have you been use the IC above? if those who have not, IC above is used or applied to the audio power amplifier. IC processing is quite good for use on amplifier home, or room. IC used is SI1020G who have not very high output with only 20W 8 ohm impedance speakers. Supply voltage ranging from 12 volt to 23 volts.



Below schematic audio amplifier with IC SI1020G
Part List
R1 = 100K
R2 = 1R
C1 = 2u2F
C2 = 100uF
C3 = 47uF
C4 = 10uF
C5 = 2200uF
C6 = 47uF
C7 = 100uF 
[Continue reading...]

Tuesday, October 28, 2014

TDA7383 35W Car Quad Audio Amplifier diagram

- 0 comments
The following a 4 x 35 watts channels/quad audio power amplifier circuit based IC TDA7383. The amplifier circuit is designed specifically suitable for car audio system applications. With a fairly large output power per channel, low distortion and low output noise features. Heatsink should be installed on the power IC to avoid excessive heat. There are very simple and easy to build cos only a few additional components outside the IC power.

Circuit  4 x 35W Car Audio Amplifier TDA7383


IC TDA7383 is a new technology class AB Audio Power Amplifier in Flexiwatt 25 package designed for high end car radio applications. Thanks to the fully complementary PNP/NPN output configuration the TDA7383 allows a rail to rail output voltage swing with no need of bootstrap capacitors. The extremely reduced components count allows very compact sets. The on-board clipping detector simplifies gain compression operations. The fault diagnostics makes it possible to detect mistakes during Car- Radio assembly and wiring in the car.

Absolute Maximum Ratings of IC TDA7383
Operating Supply Voltage : 18 V
DC Supply Voltage : 28 V
Peak Supply Voltage (t = 50ms) : 50 V
Output Peak Current Repetitive (Duty Cycle 10% at f = 10Hz): 4.5 A
Output Peak Current Non Repetitive (t = 100µs) : 5.5 A
Power dissipation, (Tcase = 70°C) : 80 W
Junction Temperature : 150 °C
Storage Temperature : – 55 to 150 °C
[Continue reading...]

Friday, October 3, 2014

5 Watt Class A Audio Amplifier

- 0 comments

On the day of the old valve, most commercial audio amplifiers suitable for compact integrated single discs or players used stereo amplifier topology of a single valve. The circuit is usually carried out through a multiple type valve, for example, a triode pentode ECL86.

Common features of the amplifiers are Class A operation, the output power in the 3 - 5W range, input sensitivity of about 600mV of total output power, THD of 3% @ 1KHz and 3W. Best types showed figures of 1.8% THD @ 3W and 0.8% @ 2W.

This solid-state push-pull single-ended Class A circuit is capable of providing a sound comparable to that of tube amplifiers, offering more output power (6.9W measured across a load of 8 ohm speaker cabinet), less THD, higher input sensitivity and better linearity.

Voltage and current for this circuit is 24 V and 700 mA, respectively, compared with 250 HT rail and 1A@6.3V heating filament of the valve works with amplifiers. The penalty only for the transistor circuit that works with the need for a larger heat sink for Q2 and Q3 (compared with the maximum power delivered). In any case, the amount of heat generated by this circuit can be comparable to that of a single valve amplifier. A choice of low-boost facility can be added through R5 and C5.

This circuit was built and compared with a circuit of a valve box phonograph in the early 1950 by Aren van Waard, a Dutch biochemist working in the field of medical imaging (PET) with a strong interest in audio amplifiers valve. A complete description of the circuits and test results of subjective comparisons made by the distinguished author appeared in the magazine AudioXpress: February, March and April 2005 issues.
[Continue reading...]

Monday, September 8, 2014

Stereo Audio Amplifier with IC TEA2024

- 0 comments
 The circuit above is based on IC TEA2024, package IC is SIP2-10 and manufactered by THOMSON. Circuit above can be applied anywhere as long as the speaker must be required , do not use powered speakers, it will make this circuit of hot , especially on the IC. So the use of powered speakers with the power output of this circuit.
Technical Information :
Minimum voltage : 6 Volts DC
Maximum voltage: 18Volts DC
Power Output       : 2 x 7 Watts
Impedance           : 4 Ohms
Currents               : 35 mA
[Continue reading...]

Friday, September 5, 2014

TDA 7309 Digital Audio Processor Circuit

- 0 comments

Digital Audio Processor TDA 7309 is a stereo audio processor with independent volume control of each channel was to get the audio quality of a good processor. Digital Audio Processor TDA 7309 is equipped with a loudness control is controlled externally. Digital Audio Processor TDA 7309 also has a soft mute feature stand-alone for each canals. Digital Audio Processor TDA 7309 is controlled via the I2C serial bus system with a microcontroller interface. 


Click to view larger.

Block Diagram of Digital Audio Processor TDA 7309Feature-owned Digital Audio Processor TDA 7309The input multiplexer with 3 stereo inputRecording function on the output lineLoudnes external ontrolIndependent volume controlDigital volume control with 1dB stepSoft MuteAll functions of the Digital Audio Processor TDA 7309 is programmed via the I2C serial bus system
[Continue reading...]

50W car audio amplifier schematic circuits

- 0 comments
50WCar power amplifier uses SI1050GL IC as the main amplifier. The output power 50 Watt 8 ohm mono impedance. Up to 25 Volt DC voltage. with source voltage of this amplifier car battery has to work.




Minimum of 12 Volt battery voltage, less than a sound or audio is issued less than the maximum and less good. You can assemble  this circuit amplifier with a schema like this.
50W
Part List
R1 = 100K
R2 = 1R
C1 = 2.2uF
C2 = 22uF
C3 = 100uF
C4 = 0.1uF
C5 = 100uF
U1 = SI1050GL
If you want to make stereo amplifier , you must required multiply the two of components. 


[Continue reading...]

Friday, December 27, 2013

Automatic Switch For Audio Power Amplifier

- 0 comments
Circuit of an automatic switch for audio power amplifier stage is presented here. The circuit uses stereo preamplifier output to detect the presence of audio to switch the audio power amplifier on only when audio is present. The circuit thus helps curtail power wastage. IC1 is used as an inverting adder. The input signals from left and right channels are combined to form a common signal for IC2, which is used as an open loop comparator. IC3 (NE556) is a dual timer. Its second section, i.e., IC3(b), is configured as monostable multivibrator. Output of IC3(b) is used to switch the power amplifier on or off through a Darlington pair formed by transistors T1 and T2. IC3(a) is used to trigger the monostable multivibrator whenever an input signal is sensed.

Switch For Audio Power Amplifier Circuit diagram:

Automatic Switch For Audio Power Amplifier-Circuit-Diagram

Under ‘no signal’ condition, pin 3 of IC2 is negative with respect to its pin 2. Hence the output of IC2 is low and as a result output of IC3(a) is high. Since there is no trigger at pin 8 of IC3(b), the output of IC3(b) will be low and the amplifier will be off. When an input singal is applied to IC1, IC2 converts the inverted sum of the input signals into a rectangular waveform by comparing it with a constant voltage which can be controlled by varying potentiometer VR1. When the output of IC2 is high, output pin 5 of IC3 goes low, thus triggering the monostable multivibrator. As soon as the audio input to IC1 stops, pin 5 of IC3 goes high and pin 1 of IC3 discharges through capacitor C3, thus resetting the monostable multivibrator.

Hence, as long as input signals are applied, the amplifier remains ‘on.’ When the input signals are removed, i.e., when signal level is zero, the amplifier switches off after the mono flip-flop delay period determined by the values of resistor R8 and capacitor C3. If no input signals are sensed within this time, the amplifier turns off—else it remains on. Power supply for the circuit can be obtained from the power supply of the amplifier. Hence, the circuit can be permanently fitted in the amplifier box itself. The main switch of the amplifier should be always kept on. Resistors R1 and R2 are used to divide single voltage supply into two equal parts.

Capacitors C1 and C2 are used as regulators and also as an AC bypass for input signals. Diode D1 is used so that loading fluctuations in power amplifier do not affect circuit regulation. Transisitor T2 acts as a high voltage switch which may be replaced by any other high voltage switching transistor satisfying amplifier current requirements. Value of resistor R10 should be modified for large current requirement. The LED glows when the amplifier is on. The circuit is very useful and relieves one from putting the amplifier on and off every time one plays a cassette or radio etc.
Source :  http://www.ecircuitslab.com/2012/01/simple-automatic-switch-for-audio-power.html
[Continue reading...]

Boomer Audio Power Amplifier Using LM4906

- 0 comments
The well-known LM386 is an excellent choice for many designs requiring a small audio power amplifier (1-watt) in a single chip. However, the LM386 requires quite a few external parts including some electrolytic capacitors, which unfortunately add volume and cost to the circuit. National Semiconductor recently introduced its Boomer® audio integrated circuits which were designed specifically to provide high quality audio while requiring a minimum amount of external components (in surface mount packaging only). The LM4906 is capable of delivering 1 watt of continuous average power to an 8-ohm load with less than 1% distortion (THD+N) from a +5 V power supply. The chip happily works with an external PSRR (Power Supply Rejection Ratio) bypass capacitor of just 1 µF minimum.

In addition, no output coupling capacitors or bootstrap capacitors are required which makes the LM4906 ideally suited for cellphone and other low voltage portable applications. The LM4906 features a low-power consumption shutdown mode (the part is enabled by pulling the SD pin high). Additionally, an internal thermal shutdown protection mechanism is provided. The LM4906 also has an internal selectable gain of either 6 dB or 12 dB. A bridge amplifier design has a few distinct advantages over the single-ended configuration, as it provides differential drive to the load, thus doubling output swing for a specified supply voltage. Four times the output power is possible as compared to a single-ended amplifier under the same conditions (particularly when considering the low supply voltage of 5 to 6 volts).

Boomer Audio Power Amplifier Circuit diagram:


When pushed for output power, the small SMD case has to be assisted in keeping a cool head. By adding copper foil, the thermal resistance of the application can be reduced from the free air value, resulting in higher PDMAX values without thermal shutdown protection circuitry being activated. Additional copper foil can be added to any of the leads connected to the LM4906. It is especially effective when connected to VDD, GND, and the output pins. A bridge configuration, such as the one used in LM4906, also creates a second advantage over single-ended amplifiers. Since the differential outputs, Vo1 and Vo2, are biased at half-supply, no net DC voltage exists across the load.

This eliminates the need for an output coupling capacitor which is required in a single supply, single-ended amplifier configuration. Large input capacitors are both expensive and space hungry for portable designs. Clearly, a certain sized capacitor is needed to couple in low frequencies without severe attenuation. But in many cases the speakers used in portable systems, whether internal or external, have little ability to reproduce signals below 100 Hz to 150 Hz. Thus, using a large input capacitor may not increase actual system performance. Also, by minimizing the capacitor size based on necessary low frequency response, turn-on pops can be minimized.

Source: http://www.ecircuitslab.com/2011/06/boomer-audio-power-amplifier-using.html
[Continue reading...]

Thursday, December 26, 2013

1W BTL Audio Amplifier

- 0 comments
The TDA8581(T) from Philips Semiconductors is a 1-watt Bridge Tied Load (BTL) audio power amplifier capable of delivering 1 watt output power into an 8-Wload at THD (total harmonic distortion) of 10% and using a 5V power supply.

The schematic shown here combines the functional diagram of the TDA8551 with its typical application circuit. The gain of the amplifier can be set by the digital volume control input. At the highest volume setting, the gain is 20 dB. Using the MODE pin the device can be switched to one of three modes: standby (MODE level between Vp and Vp–0.5 V), muted (MODE level between 1 V and Vp–1.4 V) or normal (MODE level less than 0.5 V). The TDA8551 is protected by an internal thermal shutdown protection mechanism. The total voltage loss for both MOS transistors in the complementary output stage is less than 1 V.

1 Watt BTL Audio Amplifier Circuit diagram:

1 Watt BTL Audio Amplifier Circuit Diagram


Using a 5-V supply and an 8-W loudspeaker, an output power of 1 watt can be delivered. The volume control has an attenuation range of between 0 dB and 80 dB in 64 steps set by the 3-state level at the UP/DOWN pin: floating: volume remains unchanged; negative pulses: decrease volume; positive pulses: increase volume Each pulse at he Up/DOWN pin causes a change in gain of 80/64 = 1.25 dB (typical value).

When the supply voltage is first connected, the attenuator is set to 40 dB (low volume), so the gain of the total amplifier is then –20 dB. Some positive pulses have to be applied to the UP/DOWN pin to achieve listening volume. The graph shows the THD as a function of output power. The maximum quiescent current consumption of the amplifier is specified at 10 mA, to which should be added the current resulting from the output offset voltage divided by the load impedance.

Source : http://www.ecircuitslab.com/2011/05/1w-btl-audio-amplifier-circuit-diagram.html
[Continue reading...]

Friday, April 12, 2013

TV Transmitter Audio and video IC LM1889

- 0 comments
This small circuit transmitter processes the signs of audio of a table or microphone, and the signs of video of a camera, or still the audio signs and video of a DVD, Video-cassette or even it sweats her video plate has an exit of composed video, you can transmit direct of your computer. Playing them in a channel free from the strip of VHF.
These signs can be irradiated with a common antenna and captured in an it distances of until about 500 meters that it is the most appropriate for urban areas, reminding that and necessary to be a lot of caution and careful for not interfering in frequencies of other issuing, as well as to emergency services. Depending on the local conditions (existence or not of obstacles). Fed with tensions from 12 to 15 Volts, the circuit has excellent I carry out so much in the emission of monochrome signs, as in colors. An important point of this project ‘the easiness with that he can be set up and adjusted, since only two coils are used. Ideal to be used with surveillance cameras turning the without thread.

As it Works the TV video and audio transmitter with lm1889n

The heart of this circuit transmitter ‘is the integrated circuit LM1889N of National Semiconductor, that consists of a Modulator of Video for TV in an involucres of 18 pins DIL.
This integrated circuit ‘used in videocassettes and videogames, exactly to process the image information and sound, so that they can be played in a channel free from the strip of VHF.
As it is component that ‘used in commercial equipments, besides the reliability, we have a certain obtaining easiness. The readers, with luck, until they can find this available component in an old videogame that it is out of use, and you take advantage of it to set up your station communitarian. count all the necessary stages to the processing of the video signals and audio of a transmitter of signs of TV.
The coil L1 together with the capacitor in parallel, it generates the sign of 4,5 MHz that, modulated with the sound, it should be separate from the bearer of video of this frequency. Like this, the adjustment that should do in this coil it simply consists in you take it to 4,5 MHz, in way we obtain it sound.
The audio modulation ‘done by a varicap in a very simple way, so that the intensity of the audio sign obtained in most of the exits of the sound table it should provide a good reproduction.
The video sign, that obtained ‘of the video exit of any camera, videocassette, DVD, applied in the pin 13 of the circuit integrated after going by an amplification stage with two transistors.
This sign will modulate in width the video bearer whose frequency certain ‘for L2 and the capacitor in parallel.
We should adjust the frequency of this oscillator for the channel free from the strip of VHF, usually a channel baixo(2 to 6) in that the broadcasting station will operate.
The exit of RF, obtained in the pin 11 mischievous ‘to an amplifying stage with a transistor and of this for the antenna expresses or a telescopic antenna, in case the transmission is of short reach. Observe that in the modulation of audio of this circuit, the sign generates two subportator being below a 4,5 MHz above the frequency of the channel and other 4,5 MHz.
As one of them not eliminated ‘, she can cause interferences in the adjacent channel. That means that you should choose a free channel in your place, but that doesn’t have adjacent channels operating.
The power supply of the circuit can be made with tensions of 12 (7812) or 15(7815) Volts of a source with at least 1A and excellent filter. A deficient filter in this type of so much circuit can provoke snores in the sound, as undulations in the image.

Suggestion of power supply for circuit using the ic 7812


Schematic for assembly of the tv transmitter with lm1889n
Assembly of the circuit of the TV transmitter


The healthy resistors of 1/8W or larger. The power source so much can be the one of 12V/1A, as it can be made a modification to operate with 15V, being enough for that to change the transformer and the integrated circuit. The circuit plate printed for the assembly ‘shown below in the illustration. The coils, as always, are the elements more critics of the project. L1 ‘formed by 40 you exhale of thread enameled fine (30 to 34) in a form of 5 diameter mm and 18 height mm, with nucleus of adjustable ferrite. The form for this coil can be obtained in old radios and televisions. The coil L2 that determines the frequency of the channel can have from 2 to 6 you exhale of thread 18 to 22, in used similar form her for L1. For 2 or 3 you exhale we will have the operation in the high channels of VHF, between the 7 and the 13, and for 4 to 6 you breathe the operation it will be among the channels 2 and 6. For the entrance of audio and video important ‘to use armored threads and appropriate connectors. For the antenna to use a connector for cable of 75 Ohms. The transmission section should not be in the same box that the source. The transmitter should be shielded for larger operation stability and to avoid the reception of noises that affect the transmission. The trim pot P1 has for purpose to adjust to component DC of the video sign, important to obtain the maximum revenue in the transmission.

Adjust alignment of the video, audio, the coils, antenna and frequency of the operation
To test and to adjust the transmitter, call in your entrance the exits of audio and video of a videocassette with any ribbon of good quality. Use appropriate cables. Tie the transmitter and, in that she intend to do the operation. The antenna of the transmitter can be a piece of some centimeters of covered common thread. Adjust the coil initially L1 so that the sign of maxim image intensity is captured. Adjustment the way trimpot to obtain the best image. Then, adjust slowly the coil L2 until obtaining the sound sign. Obtaining the sound sign, retouch the tuning of way L1 to obtain the maxim transmission. If it has difficulties in obtaining the tuning in the wanted channel, alter the value of C7 or I number it of you exhale of L1. If it has difficulties in tuning in the sound, alter C6 or then the number of you exhale of L2.
Proven the operation, make the connection of the definitive antenna (it expresses or it interns) and re-do the way fittings to obtain the best transmission quality. After that, it is only to operate the station.

LIST OF MATERIAL
Power supply
  • CI1 – 7812 or 7815
  • D1 D4 1n4004 or equivalent
  • C1 C4 – 10NF
  • C5 – 2200µF TO 4700µF / 50 V
  • C6 – 100NF
  • C7 – 100µF 35V
  • C8 – 100NF
  • L1 – Shock of RF 100µH / 1 THE
  • T1 – Transformer, primary in agreement with the net (110/220) and secondary from 18 to 24V / 1A
  • Several – printed circuit board, threads, box, etc.

Semiconductors:
  • Cl1 – LM1889- Integrated Circuit – Modulator of Video
  • Q1, Q2, Q4 – BC547 or equivalent
  • Q3 – BD135 or equivalent, example 2n2218 (different Pinage)
  • D1 – BB809 VARICAP or equivalent
Resistors 1/8W, 5%:
  • R1, R15 – 82 Ohms-
  • R2 – 120 K Ohms
  • R3 – 27K Ohms
  • R4 – 1,2 K Ohms
  • R5, R13, R14 – 270
  • R6 – 470 Ohms
  • R7 – 56k Ohms
  • R8 – 68k Ohms
  • R9 – 220 K Ohms
  • R10 – 2,7 K Ohms
  • R11, R17 – 1 K Ohms
  • R12, R16. R19 – 10 K Ohms
  • R18 – 47 Ohms x 1W
  • R20 – 22 K Ohms
  • P1 – 10 K Ohms trimpot
Capacitors:
  • C1 – 4,7µF/1 6V – ELECTROLYTIC
  • C2, C3 – 10µF/1 6V – ELECTROLYTIC
  • C4, C8 – 1 nF – ceramic
  • C5 – 120 pF – ceramic
  • C6 – 47 pF – ceramic
  • C7 – 56 pF or 47 pF – ceramic
Several:
  • L1, L2 – Coils – L1 – 0.3µH and L2 – 7 to 13µH.
  • XRF – it Collides of 100 µH – to see text.
  • Several -printed board circuit , entrance Jacques and output of signs, box for assembly, power source, forms for the coils, enameled threads, etc.



[Continue reading...]
 
Copyright © 2012. Fast Diagrams - Posts · Comments
Powered by Blogger