Showing posts with label detector. Show all posts
Showing posts with label detector. Show all posts

Saturday, November 15, 2014

Parts Needed for Motion Detector Circuit

- 0 comments
This is a circuit which can detect any motion or movement. Its most common use is to detect a person moving through an area where the motion detector can sense.

For example, the motion detector may be placed near a door, so that if any person passes through this doorway, the motion detector will be triggered.

The main electronic component we will use that allows us to pick up this detection is the PIR motion sensor. The PIR motion sensor is a sensor which detects movement through picking up infrared waves. Being that a person emits infrared waves, the detector is able to detect these waves and react, according to the how the circuit is designed to react. The sensor can also pick up the movement of inanimate objects as well, such a rolling ball, because as those objects move, friction acts on them, generating heat. This heat emits infrared radiation, which the PIR sensors may be able to detect if great enough.

In our basic circuit, when the motion detector circuit picks up movement, a red LED will flicker on. 

Parts Needed for Motion Detector Circuit
  • PIR motion sensor
  • LED
  • 470Ω Resistor
  • 6V of DC power

The PIR motion sensor is, again, a sensor which can detect movement through picking up infrared radiation. Being that people naturally give off radiation, because of our generated body heat, the motion can easily detect people walking and moving through a vicinity within the sensors range.

The motion sensor has a sensitivity range up to 20 feet (6 meters) and a 110° x 70° detection range, making it a wide lens detection sensor. This means it can measure 110° vertically (from top to bottom) and 70° horizontally (from left to right). The best way to check its sensitivity is when the circuit is built, try moving around through all of its angles. See at which angles it can detect your movement and at which angles it is not able to detect your movement, meaning your out of its angle scope. A lot of it is trial and error and experimenting. Once you know where it can and cannot detect, you can place it in an optimal place where it can detect in areas where you want it to.

The PIR motion sensor is a 3-pin device

Pin 1 is the pin which receives the positive DC voltage. The PIR motion sensor needs between 5V-9VDC of power for operation. In our case, we will use about 6V of power. This can be obtained from switching a DC power supply to 6V or using 4 AA batteries connected in series. We will then feed this voltage into pin 1 of the PIR module.

Pin 3 is the negative DC voltage or ground pin of the device. We connect the negative terminal of the power source to this pin, for a return path.

Pin 2 is the Output pin of the PIR module. This is where the output of the PIR will leave from. When motion is detected by the PIR, its output will go high to 3V. When no motion is detected, its output low and it gives off practically no voltage. When high you can see then how it can power a load, such as an LED to light. This way we can know when it has detected motion or not.

In our circuit, we will connect a 470Ω resistor in series with an LED to the output pin of the PIR sensor. When motion is detected, the output of the PIR sensor will swing high and power and light the LED.

Circuit Diagram
Here you can see anywhere from 5V-9V is fed into the power pins.

Connected to the output pin is an LED. We place a 470Ω resistor in series to limit current so that the LED doesnt receive excess current.

In this circuit, when motion is detected, the output voltage swings high and powers the LED. After about 1 second or 2, the output swings back low and the LED turns off until motion is detected again. Without any motion, the LED just stays off.
[Continue reading...]

Friday, October 3, 2014

Tone Detector circuit diagrams and explanation

- 0 comments

The following circuit diagrams are tone detector circuit diagrams which also known as sound activated switch circuit. Actually, these circuits use micro-controller for switching because the circuits were designed for robot start up activation. But you can build switching module using relay.

Tone Detector diagram 1

Tone

Tone Detector diagram 2

Tone

Tone Detector diagram 3

Tone

Tone Detector diagram 4

Tone

Tone Detector diagram 5

Tone

Source: Sound activated switch for robot

[Continue reading...]

Friday, September 19, 2014

Ultrasonic Distant Obstacle Detector

- 0 comments
The first sensor a robot usually gets fitted with is an obstacle detector. It may take three different forms, depending on the type of obstacle you want to detect and also — indeed, above all — on the distance at which you want detection to take place. For close or very close obstacles, reflective IR sensors are most often used, an example of such a project appears elsewhere in this blog. These sensors are however limited to distances of a few mm to ten or so mm at most. Another simple and frequently-encountered solution consists of using antennae-like contact detectors or ‘whiskers’, which are nothing more than longer or shorter pieces of piano wire or something similar operating microswitches.

Circuit diagram:

Ultrasonic
Ultrasonic Distant Obstacle Detector Circuit Diagram

Detection takes place at a slightly greater distance than with IR sensors, but is still limited to a few cm, as otherwise the whiskers become too long and hinder the robot’s normal movement, as they run the risk of getting caught up in things around it. For obstacles more than a couple of cm away, there is another effective solution, which is to use ultrasound. It’s often tricky to use, as designers think as if they needed to produce a telemeter, when in fact here we’re just looking at detecting the presence or absence of obstacles, not measuring how far away they are. So here we’re suggesting an original approach that makes it possible to reduce the circuit required to a handful of cheap, ordinary components.

 ultrasonic distant obstacle detector Our solution is based on the howlround or feedback effect all too familiar to sound engineers. This effect, which appears as a more or less violent squealing, occurs when a microphone picks up sound from speakers that are connected to it via an amplifier. Feeding back the output signal from the speaker into the input (the microphone) in this way creates an acoustic oscillator. Our detector works on the same principle, except that the microphone is an ultrasound receiver while the speaker is an ultrasonic emitter. They are linked just by a very easily-built ordinary amplifier. Feedback from the output to the input occurs only when the ultrasonic beam is reflected off the obstacle we are trying to detect.

As Figure 1 shows, the receiver RXUS is connected to the input of a high-gain amplifier using transistors T1 and T2. As the gain of this stage is very high, it can be reduced if necessary by pot P1 to avoid its going into oscillation all on its own, even in the absence of an obstacle. The output of this amplifier is connected to the ultrasonic emitter TXUS, therby forming the loop that is liable to oscillate due to the effect of feedback. When this takes place, i.e. when an obstacle is close enough to the ultrasonic transducers, a pseudo-sine wave signal at their resonant frequency of 40 kHz appears at the amplifier output, i.e. at the terminals of the transmitting transducer.

This signal is rectified by D1 and D2 and filtered by C3 and, if its amplitude is high enough, it produces a current in R6 capable of turning transistor T3 on to a greater or lesser extent. Depending on the nature and distance of the obstacle, this process does not necessarily happen in a completely on/off manner, and so the level available at T3 collector may be quite poorly-defined. The Schmitt CMOS invertors are there to convert it into a logic signal worthy of the name. So in the presence of an obstacle, S1 goes high and S2 goes low. Powering can be from any voltage between 5 and 12 V.

The gain, and hence the circuit’s detection sensitivity, does vary a bit with the supply voltage, but in all cases P1 makes it possible to achieve a satisfactory setting. Although it is very simple, under good conditions this circuit is capable of detecting a normally-ultrasound-reflective obstacle up to around 5 or 6 cm away. If a smaller distance is needed, you simply have to reduce the gain by adjusting P1. Building the circuit is straightforward. Both transducers are 40 kHz types that can be found in any retailers, and the other components couldn’t be more ordinary.  in Figure 2.
[Continue reading...]

Thursday, September 11, 2014

Gamer Lie Detector Wiring diagram Schematic

- 0 comments
This is a simple Gamer Lie Detector Circuit Diagram. The two probes shown are held in the hands and the skin resistance applies bias to the transistor. The 5 k ohm pot is set for zero deflection on the meter. When the subject is embarrassed or lies, sweating on the hands takes place, increasing the bias to the transistor and upsetting the bridge balance.

Gamer Lie Detector Circuit Diagram


Gamer

[Continue reading...]

Monday, September 8, 2014

Infrared Proximity Detector Wiring diagram Schematic

- 0 comments
This proximity detector using an infrared detector (Fig. 1) can be used in various equipment like automatic door openers and burglar alarms. The schema primarily consists of an infrared transmitter and an infrared receiver.

Infrared

Fig. 1: IR proximity detector

The transmitter section consists of a 555 timer IC functioning in astable mode. It is wired as shown in the figure. The output from astable is fed to an infrared LED via resistor R4, which limits its operating current. This schema provides a frequency output of 38 kHz at 50 per cent duty cycle, which is required for the infrared detector/receiver module. Siemens SFH5110-38 is a much better choice than SFH506-38. Siemens SFH5110-38 is turned on by a continuous frequency of 38 kHz with 50 per cent duty cycle, whereas SFH506 requires a burst frequency of 38k to sense. Hence, SFH5110-38 is used.

The receiver section comprises an infrared receiver module, a 555 monostable multivibrator, and an LED indicator. Upon reception of infrared signals, 555 timer (mono) turns on and remains on as long as infrared signals are received. When the signals are interrupted, the mono goes off after a few seconds (period=1.1 R7xC6) depending upon the value of R7-C6 combination. Thus if R7=470 kilo-ohms and C6=4.7µF, the mono period will be around 2.5 seconds.



Fig. 2: Proposed arrangement for separation of IR LED and receiver module in the proximity detector

Both the transmitter and the receiver parts can be mounted on a single breadboard or PCB. The infrared receiver must be placed behind the infrared LED to avoid false indication due to infrared leakage.

An object moving nearby actually reflects the infrared rays emitted by the infrared LED. The infrared receiver has sensitivity angle (lobe) of 0-60 degrees, hence when the reflected IR ray is sensed, the mono in the receiver part is triggered. The output from the mono may be used in any desired fashion. For example, it can be used to turn on a light when a person comes nearby by energising a relay. The light would automatically turn off after some time as the person moves away and the mono pulse period is over.

The sensitivity of the detector depends on current-limiting resistor R4 in series with the infrared LED. Range is approximately 40 cm. For 20-ohm value of R4 the object at 25 cm can be sensed, while for 30-ohm value of R4 the sensing range reduces by 22.5 cm.

(Note. The author procured the samples of Siemens products from Arihant Electricals, New Delhi, the distributor of Siemens in India.)

This schema costs around Rs 125.



Sourced By: EFY Author :  K.S. Sankar
[Continue reading...]

Thursday, December 26, 2013

Simple Active ir Motion Detector Circuit Diagram

- 0 comments
To explore how different motion detectors operate.To successfully build and test an ambient-light-ignoring active IR motion detector.

Background
 There are a wide variety of motion detectors available currently. To allow a better understanding of motion detectors,the following section provides a detailed description of a few different types.

Ultrasonic Motion Detectors
Ultrasonic transducers can be used to detect motion in an area where there are not supposed to be any moving objects.This type of motion detector is most commonly used in burglar alarm systems since they are very effective in this application.


 Figure 1 shows the operation of an ultrasonic motiondetector. There are tw1o transducers: one emits an ultrasonicwave and the other picks up reflections from the differentobjects in the area. The reflected waves arrive at the receiverin constant phase if none of the objects in the area are moving.If something moves, the received signal is shifted in phase. 

A phase comparator detects the shifted phase and sends a triggering pulse to the alarm.Ultrasonic motion detectors have certain advantages and disadvantages when compared with other types of motion detectors. The main advantages is that they are very sensitive and extremely fast acting. However, the largest problem with this type of motion detector is that it sometimes responds to normal environmental vibration that can be caused by a passing car or a plane overhead. Some types of motion detectors use infrared sensors to avoid this problem, but even these detectors have some problems.

 Passive Infrared Motion DetectorIn passive infrared motion detectors, a sensorcontaining an infrared-sensitive phototransistor is placed in thearea to be protected. Circuitry within the sensor detects theinfrared radiation emitted by the intruder`s body and triggersthe alarm. 

The problem with using this type of detector is that it can be falsely triggered by warm air movement or other disturbances that can alter the infrared radiation levels in an area. In order to prevent this problem, newer systems use tw1oinfrared sensors which monitor different zones within a protected area. Logic within system triggers the alarm only when the tw1o zones are activated in sequence, as would occur if a person walked through the protected area.

Active Infrared Motion Detector


Figure 2 shows the operation of an active infrared motion detector. In the active system each sensor consists oftw1o housings. One housing contains an infrared-emitting diode and an infrared-sensitive photo transistor. The other housing contains an infrared reflector.When positioned in front of an entrance to a protected area, the tw1o housings establish an invisible beam. A person entering the area interrupts the beam causing an alarm to be triggered. An active motion detector is much more reliable than a passive one, but it requires careful alignment when it is installed. The detector can be falsely triggered if one of the housings moves slightly and causes a discontinuous beam.

Project
 For our project, we decided to construct an activeinfrared motion detector. Originally, we wanted to build both anIR and an ultrasonic detector, but we decided that an ultrasonicdetector would require too much time for a three week project.However, we also decided that just building an IR motiondetector would probably be a trivial exercise. 

So, we decided to expand on the concept by building an ambient light ignoring motion detector.This type of motion detector uses the same basic concept as the active infrared motion detector. An interruption in a 5kHz modulated pulsating beam that is transmitted by an infrared diode and received by an infrared transistor sets off the alarm. A schematic of this motion detector is given in Figure 3.

Simple Active ir Motion Detector  Circuit Diagram

 Figure 3. Ambient-Light-Ignoring Active Motion Detector

The circuit on the left is the transmitter circuit that establishes a 5 kHz modulated infrared beam. As you can see from the schematic of the receiver circuit, a resonance-handbarrow amplifier reduces the detector`s sensitivity to stray light. C1 and L1 in IC2A`s feedback loop cause the op amp to pass only those frequencies at or near the LED`s 5 kHz modulation rate. IC2B`s output increases when the received signal is sufficient to drop the negative voltage across C2 below the reference set by R2. The output of this circuit is then attached to some load resistance, which can be an alarm or, for demonstration purposes, an LED.
[Continue reading...]

Wednesday, May 1, 2013

Temperature Detector For Fan Controller

- 0 comments
The fan controller circuit for the Titan 2000 and other AF heavy-duty power amplifiers, has an output that sets a voltage if the fan controller reaches the end of its range. Since the controller responds to temperature, this signal is seen by the amplifier protection circuitry as an over temperature indication. The disadvantage of this output is that the maximum voltage for the fans is not constant, but depends on the load (number of fans, defective fans) and the mains voltage. This variation is caused by the fact that the supply voltage for the output stage is taken directly from the filtered transformer voltage.

Maximum Temprature Detector For Fan ControllerIf the fans should fail, for example, the maximum temperature limit would lie at a considerably higher level than the desired value. The accompanying circuit, which compares the magnitude of the fan voltage to a fixed reference value, has been developed to allow the maximum temperature to be reliably detected. This circuit is tailored for 12-V fans. The reference voltage is generated by the ‘micro power voltage reference’ D1 and the FET T1, which is wired as a current source. These components are powered directly from the applied fan voltage. The current source is set up to deliver approximately 50µA.

D1 can work with as little as 10µA. The supply voltage for the IC is decoupled by R10, C3 and C4, with D4 providing over voltage protection. A maximum supply voltage of 16 V is specified for the TLC271. This opamp works with a supply voltage as low as 3 V and can handle a common-mode voltage up to approximately 1.5 V less than the positive supply voltage. Accordingly, 1.2 V has been chosen for the reference voltage. The fan voltage is reduced to the level of the reference voltage by the voltage divider R2–R3–P1. The limits now lie at 11.2 V and 16.7V.

If you find these values too high, you can reduce R2 to 100 kΩ, which will shift the limits to 9.5 V and 14.2 V. The output of the voltage divider is well decoupled by C2. A relatively large time constant was selected here to prevent the circuit from reacting too quickly, and to hold the output active for a bit longer after the comparator switches states. A small amount of hysteresis (around 1 mV) is added by R4 and R5, to prevent instability when the comparator switches. D2 ensures that the magnitude of the hysteresis is independent of the supply voltage. Two outputs have been provided to make the circuit more versatile.

Output ‘R’ is intended to directly drive the LED of an optocoupler. In addition, transistor T2 is switched on by the output of the opamp via R7 and R8, so that a relay can be actuated or a protection circuit triggered using the ‘T’ output. The high-efficiency LED D3 indicates that IC1 has switched. It can be used as a new ‘maximum’ temperature’ indicator when this circuit is added to the fan controller. The circuit draws only 0.25 mA when the LED is out, and the measured no-load current consumption (with a 12.5V supply voltage) is 2.7 mA when the LED is on.

Resistors:
  • R1 = 22kΩ
  • R2 = 120kΩ
  • R3 = 10kΩ
  • R4,R6 = 1kΩ
  • R5 = 1MΩ
  • R7,R8 = 47kΩ
  • R9 = 3kΩ9
  • R10 = 100Ω
  • P1 = 5kΩ preset
Capacitors:
  • C1,C3 = 100nF
  • C2 = 100µF 25V radial
  • C4 = 47µF 25V radial
Semiconductors:
  • D1 = LM385-1.2
  • D2 = BAT85
  • D3 = high-efficiency-LED
  • D4 = zener diode 16V/1W3
  • T1 = BF245A
  • T2 = BC547B
  • IC1 = TLC271CP
Miscellaneous:
  • K1 = 2-way PCB terminal block, raster 5mm
  • K2 = 3- way PCB terminal block, raster 5mm
[Continue reading...]
 
Copyright © 2012. Fast Diagrams - Posts · Comments
Powered by Blogger